Home » Greenhouse Cover Cleaning: Dust, Algae and the Light You Are Losing

Greenhouse Cover Cleaning: Dust, Algae and the Light You Are Losing

A consultant's view of greenhouse cover cleaning: where transmission goes, what the light loss is worth in planning terms, safe cleaning methods for film and polycarbonate, and how to decide when cleaning is no longer enough.
Channel rows running the length of a bright house, transmission the condition of the skin above decides

Light is the input a greenhouse cannot store, and a dirty cover taxes every hour of it. The loss is gradual — a film of dust here, an algae patch there — so nobody notices the week it happens, only the season it costs. For a commercial farm, greenhouse cover cleaning is the cheapest light available: no capital, no permits, just scheduled labour and a method that does not damage the material. This article sets out where transmission goes, what the loss is worth in planning terms, how to clean film and polycarbonate without hurting either, and how to decide when cleaning has stopped being enough.

Where Transmission Goes: Six Sources of Cover Loss

On most farms the light is lost to six things: dust from surroundings and farm traffic, algae and hard-water scale, bird droppings, condensate films on the inner face, additive and coating aging, and leftover shading compounds.

  • Dust: field ploughing next door, gravel roads and unmetalled yards are the usual suspects; the dirty band is often thickest on the windward slope and near the gables.
  • Algae and scale: green film where condensate or drips run repeatedly, plus mineral scale wherever hard water has evaporated off the cover — worst on shaded, wet, north-facing slopes.
  • Bird droppings: negligible farm-wide, but each patch blocks locally and bakes on under strong sun, so it removes itself from the schedule only by being wiped early.
  • Inner condensate film: when the anti-drip behaviour of a film fades, droplets hang instead of running to the gutter, and the hanging film scatters light both ways.
  • Additive and UV-layer aging: a gradual multi-year decline that cleaning cannot touch, because the loss is inside the material.
  • Shading residue: whitewash or net residue left past the season it was needed; it keeps blocking light until it is actively removed.

How Much Light You Are Losing: Planning Ranges

Precise percentages depend on the site, the material and the season, so plan with ranges and stated assumptions rather than single numbers. The figures below are planning ranges for a typical commercial site — not guarantees — and the only number that matters is the one measured on your own cover.

Source of lossTypical planning range (with assumptions)Response
Dust on filmRoughly 3–10% within the first season on a dusty or field-adjacent site; low end where rain regularly washes the slopeScheduled wash before the high-light season
Algae film and scaleSeveral percentage points locally, concentrated on shaded wet slopes; worse where hard water drips uncheckedFix the drip source, then clean the film
Inner condensate film2–5% or more when anti-drip performance has faded on an aging filmRecoverable by cleaning only in part; plan re-cover
UV and additive agingGradual decline over the film’s service years; depends on grade and warrantyNot cleanable — budget for re-cover
Bird droppingsLocalised patches; small farm-wide but persistentWipe during routine rounds, not annually
Shading residueVisible whitening; persists until removedStrip with a designated remover at season end

Note how the rows split: everything above the condensate line is cleanable, everything below it is a material decision. The transmission expectations themselves differ sharply by material — glass, polycarbonate and film age differently — and the covering materials comparison sets that baseline.

Cleaning Methods and Where the Damage Comes From

The safe method is water, a soft brush and time; most cover damage comes from pressure washers, hard bristles and people on roofs. A telescopic pole with a soft brush head, working top-down, followed by a low-pressure rinse, clears dust and most algae without touching the material.

Three risks deserve standing rules:

  • High-pressure jets tear aged film and drive water under laps and into polycarbonate flutes. If a washer is used at all, keep it low pressure and oblique, well off the surface.
  • Cleaner residue must never reach irrigation water. If detergents or algae treatments are used, capture the runoff or avoid them near collection gutters entirely, and rinse thoroughly.
  • Roof work is the real safety cost: anchor points, dry conditions, and nobody walking on purlins between glass or on polycarbonate sheets without load-spreading boards.

Polycarbonate and Film: Different Enemies, Different Limits

Film fails from the outside in — UV on the outer face, dust on top of it — while polycarbonate fails quietly inside the sheet, which is why the checks differ.

On polycarbonate, algae colonises the flutes and hard-water scale forms at every persistent drip, and neither cleans easily once established; the UV-coated face must never see abrasives or solvents, or the coating that protects the sheet is the thing being cleaned off. Replace sections where flutes run green and fix the drip sources, because algae on polycarbonate returns to the same wet corner every season. On film, watch the condensate behaviour instead: droplets running cleanly to the gutter mean the anti-drip surface still works, while drips on the crop mean the film is past its additive life and cleaning will not buy that performance back. The functional layers involved — anti-drip and diffusing coatings — age on their own schedule.

Channel rows running the length of a bright house, transmission the condition of the skin above decides
Every lux lost is lost at the cover first

Cover Cleaning Frequency and Seasonal Windows

Clean before the high-light season, and again after dusty events; in temperate climates that usually means late winter to early spring, with a second pass where the site is dusty or a neighbouring field has been worked. Avoid midsummer middays, when the crew carries the heat risk and the removed dust only settles again on ventilated houses, and avoid frost, when film and coatings are at their most brittle.

Put the window in the annual maintenance calendar rather than waiting for someone to notice the dirt, and pair it with the timing of shading work: whitewash goes on as light climbs and must come off cleanly at season end, which is a scheduling decision covered with the shading nets and whitewash strategy.

Clean or Re-Cover: Making the Call

Cleaning pays when transmission recovers to near the material’s expected level; re-covering wins when a clean cover still tests well below it, because the loss sits in the material, not on it. The comparison is straightforward: cleaning labour, water and access equipment against the re-cover cost per square metre and the film warranty left to run. On multi-bay sites, clean one bay first and compare production and readings against an uncleaned bay before committing the whole house — the difference between the two bays is the value of the wash, measured rather than assumed.

Measuring Transmission with a Handheld Lux Meter

A single handheld lux meter, used consistently, tracks cover condition well enough to decide between washing and re-covering. The method matters more than the meter: take paired readings outside and inside at fixed grid points, under clear sky, within a narrow window around midday, and compute the inside-to-outside ratio for each point. The ratio — not the absolute lux figure — is what you log and compare season to season, because a cloudy morning changes the absolute number but barely moves a clean cover’s ratio.

Lux is a human-eye-weighted measure, so treat it as a trend tool rather than a full PAR audit; for DLI targets and supplemental lighting decisions, the LED vs HPS and PPFD/DLI guide covers the measurement basis. What the lux survey gives you is the before-and-after number that makes the cleaning budget defensible: the wash that lifts the ratio back to expectations pays for itself in weeks, and the one that does not tells you the cover is finished.

Lettuce rows under a clean translucent cover, the diffused light a washed cover passes to the crop
Clean cover, even light

Greenhouse cover cleaning will not add light the site never had, but it reliably hands back what dust and algae took — and the lux meter is what turns that claim from an opinion into a number worth planning around.

FAQs About Greenhouse Cover Cleaning

How much light does a dirty greenhouse cover actually lose?

A planning range of roughly 3–10% within one season on a dusty site for film, with more possible from algae and scale in wet corners. Measure inside-to-outside with a lux meter rather than assuming — sites differ too much for a single number.

Can I pressure-wash polycarbonate?

Only at low pressure and an oblique angle. High-pressure jets force water into the flutes and can strip or scratch the UV coating, and abrasives or solvents should never touch the coated face at all.

What is the best time of year to clean greenhouse covers?

Before the high-light season — late winter to early spring in temperate climates — with a second pass after dusty events or nearby field work. Avoid frost and midsummer middays for both material and crew reasons.

Will cleaning remove whitewash shading from the cover?

Not with water alone; whitewash needs a designated remover or comes off gradually through the winter. Plan the removal as part of the shading cycle, not as an afterthought to the wash.

How do we know the cover is too old rather than just dirty?

Clean a section properly and re-measure. If transmission recovers to near the material’s expected level, cleaning is the tool; if a spotless cover still tests well below it, the loss is additive and UV aging, and the budget belongs in re-covering.

Related Reading

Next Step: What to Send for a Quotation

Cover choice and cover care are the same decision made at two different dates: what a material loses to dust and algae over its first seasons should be part of the buying conversation, not a surprise afterwards.

Planning a new house, a re-cover, or a cleaning programme? For RFQ or project consultation, send: greenhouse dimensions and the number of bays; system type and channel section (100×50 mm, 73×62 mm MGS or substrate gutter); target crop; site exposure — neighbouring fields, roads, coastal dust; cover material and age, or the material under consideration; measured inside-to-outside light ratios if available; local rainfall and water hardness; delivery schedule; and the budget band. G AND N FORTUNE LIMITED supplies greenhouse structures and covers, NFT channels, DWC and Dutch bucket systems quoted to those parameters.

Table of Contents

Planning a Hydroponic Project?

Need help choosing a growing system or equipment? Tell us about your project requirements.

Discuss Your Project
CONTINUE EXPLORING
Back to News
KEEP EXPLORING

Related Articles

Continue exploring practical insights on hydroponic systems, crop growing, equipment selection, and commercial farm projects.

View All Articles
Lettuce channels running inside a covered house, the sheltered crop side of an exposed site wind plan
Planning a greenhouse windbreak around real site exposure: wind data to collect, shelter forms compared, height and distance ranges, and the side effects that change
Rolls of woven screen fabric stacked in a warehouse, the material that becomes a thermal or insect screen
A project-side look at thermal screen drive hardware: tube motor versus rack and pinion, travel and limit setting, where a closed screen leaks heat, fabric
Lettuce rows inside an arched film greenhouse with diffuse daylight spreading evenly across the canopy
A buyer-side explanation of greenhouse film additives: how anti-drip controls condensate and disease pressure, what light diffusion does to canopy uniformity, what IR layers do
TURN KNOWLEDGE INTO ACTION

Have a Hydroponic Project in Mind?

From growing system selection to equipment planning, share your project requirements with G&N Fortune and explore suitable solutions for your needs.

Prefer email? info@gnhydroponic.com

Request a Project Quote

Tell us about your requirements. Our team will review your inquiry and contact you about the next steps.