Home » Insulating Exposed Lines: Heat Gain and Pipe Sweat Control

Insulating Exposed Lines: Heat Gain and Pipe Sweat Control

A project-engineering guide to insulating exposed lines: heat gain on bare pipes, why pipe sweat drips onto crops, and which insulation material survives a greenhouse.
Stacked white foam sheets in close view, the closed-cell material pipe insulation echoes

Exposed pipe runs in a greenhouse are heat exchangers whether you asked for it or not. In summer a bare main crossing a bright bay absorbs enough radiation and warm air to push the solution several degrees past the tank temperature by the time it reaches the far end; in winter the same pipe carrying chilled water sweats and drips onto the crop below. Insulating exposed lines solves both problems with the same material, but only if the thickness, seams and UV protection are decided on purpose rather than left to whoever fits the pipe.

What Insulating Exposed Lines Actually Changes

Insulation does two jobs, and the priority differs by season. Against heat gain, it slows the transfer of greenhouse air and radiation into the solution. As a planning range, a bare 63 mm PVC main carrying solution at 18 °C through a 35 °C bay can add roughly 1–3 °C along a 40–60 m run, assuming full sun on the pipe and moderate flow; the same run in 13–19 mm closed-cell foam typically holds the rise within 0.5–1 °C. Against heat loss in winter, the same layer keeps heated supply lines from dumping energy into the air before it reaches the crop.

What insulation does not do: cool anything. A chilled line in a warm house still trends toward ambient, just slowly. Insulation buys time and stability, which is exactly what root-zone temperature control needs, and it moves the thermal fight into the tank and the water chiller sizing decision, where it belongs.

Pipe Sweat: When Condensation Becomes a Crop Problem

Pipe sweat is condensation on any surface colder than the dew point of the surrounding air. A chilled main at 12–15 °C inside a greenhouse holding 80% relative humidity at 22 °C has a dew point near 18–19 °C, so the pipe sweats continuously, and every drop follows the lowest point of the pipe until it falls — usually onto one unlucky row or one permanently wet patch of floor. Over weeks that patch becomes a moss, algae or disease nursery.

Three responses, in order of effectiveness:

  • Insulate below the dew point differential: any chilled or cool line inside the crop envelope gets a vapour-tight jacket, not just a foam sleeve left open at seams.
  • Route condensate deliberately: where insulation is impractical, fit drip trays and a collection path, consistent with how the farm already manages floor drainage and hygiene zoning.
  • Warm the solution slightly: where the crop tolerates it, lifting a chilled line 2–3 °C moves its surface above the dew point and the sweating stops. Confirm the crop’s root-zone window first.

Recovered condensate is clean water and worth routing back where the design allows — the economics are covered in the article on condensate and chilled-water recovery.

Material Choice: Foam Sleeves, Foil Wraps and What Survives

Greenhouse service is wet, bright and physically knocked about, so the material decision is as much about survival as thermal value. The realistic options:

MaterialTypical service thicknessStrengthsWatch-outs
Closed-cell elastomeric foam (rubber-based)13–25 mmBuilt-in vapour barrier, flexible, handles wet serviceUV degrades the surface; needs jacket or paint outdoors
Expanded PE foam sleeve13–25 mmCheap, quick to fit, common on supply mainsSeam separation over time; lower temperature ceiling
Aluminium foil-faced wrapOver foam coreReflects radiation, mechanical protection, UV-stable skinOnly as good as the foam beneath; seams need taping
Insulated composite pipeFactory bondedConsistent quality, no on-site seam workHigher cost, fixed radii, ordered per run

Inside the envelope, closed-cell foam at 19–25 mm on chilled lines and 13–19 mm on warm supply lines is the usual specification. Anything exposed to direct sun — yard piping, external risers — needs a UV-stable jacket or foil facing, because bare foam powdering off in one season is a common and avoidable sight. The ageing behaviour of the pipe itself under the same sun is treated separately in the article on UV ageing of exposed pipework.

Stacked white foam sheets in close view, the closed-cell material pipe insulation echoes

Installing Insulation So It Lasts

Most insulation failures are seam failures, not material failures. Water vapour finds any gap, condenses under the foam, and the layer becomes a wet bandage that holds moisture against the pipe. The workmanship rules are short: butt joints tightly, tape every longitudinal and butt seam with the manufacturer’s vapour-tight tape rather than general-purpose duct tape, seal terminations at fittings and flanges, and stagger the joints on a second layer if thickness demands one.

Coordinate with the pipe supports before fitting: sleeves must pass through or be interrupted cleanly at every clip, and a support clamped over foam compresses it into a thermal bridge at exactly the points that count. The support spacing itself is a separate subject in greenhouse pipe support hardware, but the ordering matters here — supports fixed with the insulation in mind save the whole layer. And where expansion movement is expected, allow the foam to flex with the pipe; a rigid seam over a moving joint opens within a season, as anyone who has watched PVC thermal expansion work on a hot day already knows.

Sectioned slab pieces on a green mat, the layered fit insulated pipe joints are pressed into

Where Insulation Pays and Where It Does Not

Insulate by consequence, not uniformly. Payback is clear on chilled and cool lines inside the crop envelope, on any line where sweating drips onto crop or floor, on long supply mains to the far ends of a site, and on heated root-zone supply runs. It is marginal on short distribution stubs inside shaded ducts, on drain lines, and on lines whose temperature deliberately follows air temperature. Spend the budget where a degree of solution temperature or a dry row of lettuce is worth something; leave the rest bare and visible for inspection.

Insulating exposed lines is a seasonal stability decision made once at installation. Specified by consequence — vapour-tight on everything below dew point, UV-jacketed outside, seams taped like it matters — the same layer holds solution temperature in August and keeps the rows dry in January.

FAQs About Insulating Exposed Lines

How much temperature rise does a bare pipe actually suffer in summer?

As a planning range, a bare 63 mm main carrying 18 °C solution through a fully sunlit 35 °C bay adds roughly 1–3 °C over a 40–60 m run, assuming moderate flow. 13–19 mm closed-cell foam typically holds that rise to under 1 °C. Measure on your own run before setting targets.

Why does the pipe sweat only in certain bays?

Condensation follows dew point, and dew point follows humidity. Bays with high humidity, dense canopy or poor air movement sweat first. A chilled line that is dry in one house and dripping in another is telling you where the air is wetter, not where the pipe is colder.

Is ordinary PE foam sleeve enough for a chilled line?

Only if every seam is taped vapour-tight. Chilled lines condense water inside the insulation layer itself; an open seam turns the sleeve into a wet wrap. Closed-cell elastomeric foam with taped joints is the safer specification for anything below the dew point.

Does insulation change how much the chiller has to run?

Yes, in the right direction but modestly. Insulation slows heat gain into the distribution system; the tank surface and recirculation duty still dominate the chiller load. Size the chiller for the real load and treat insulation as the measure that keeps the distribution from adding to it.

What thickness should we specify for supply mains?

As a planning range: 13–19 mm on warm or ambient supply lines inside the envelope, 19–25 mm on chilled or cool lines, and any outdoor section also jacketed against UV. Confirm against the pipe diameter and the coldest duty the line carries.

Related Reading

Next Step: What to Send for a Quotation

Insulation is quoted per metre of pipe and per condition, and the conditions differ inside the envelope, outdoors and below dew point. Sending those distinctions with the pipe list is what gets a complete price.

Specifying or upgrading pipework? For RFQ or project consultation, send: pipe diameters, materials and run lengths by section; which sections carry chilled, ambient or heated solution; greenhouse temperature and humidity ranges; any sections exposed to sun or washdown; support layout status; spares ratio; delivery schedule; and the budget band. G AND N FORTUNE LIMITED supplies piping systems, insulation and matched hardware quoted to those parameters.

Table of Contents

Planning a Hydroponic Project?

Need help choosing a growing system or equipment? Tell us about your project requirements.

Discuss Your Project
CONTINUE EXPLORING
Back to News
KEEP EXPLORING

Related Articles

Continue exploring practical insights on hydroponic systems, crop growing, equipment selection, and commercial farm projects.

View All Articles
Channel rows running the depth of a house, the load a farm grid application has to size for
A planning guide to grid connection for hydroponic farms: demand estimation, transformer choices, application paperwork, approval timelines and connection costs.
Sprinkler arcs crossing open ground, the daytime services a standby generator keeps alive overnight
The fuel side of farm standby power: day tanks, transfer pumps and filters, diesel ageing in storage, and the test-run discipline that keeps the generator
Herb plant growing in a net pot, the crop a controller schedule feeds from stored setpoints
A practical guide to controller program backups: what to export and how often, restore drills, backup media choices and version notes that survive staff turnover.
TURN KNOWLEDGE INTO ACTION

Have a Hydroponic Project in Mind?

From growing system selection to equipment planning, share your project requirements with G&N Fortune and explore suitable solutions for your needs.

Prefer email? info@gnhydroponic.com

Request a Project Quote

Tell us about your requirements. Our team will review your inquiry and contact you about the next steps.